MicoAir743 V2 Flight Controller
Rs. 5,699.00
Skip to product information
MicoAir743 V2 Flight Controller
Rs. 5,699.00
The MicoAir743 V2 is a 480MHz STM32H743 flight controller for ArduPilot, PX4, INAV and Betaflight. It packs dual IMUs, a barometer, an onboard compass, an analog OSD, microSD logging and built-in Bluetooth telemetry, with 8 UARTs, 11 PWM outputs and a dedicated DJI O3/O4 connector.
This listing is the flight controller only, with no ESC. If you want it paired with a matching 4-in-1 ESC, see the MicoAir743 V2 AM32 Stack.
Features
- STM32H743VIT6 at 480MHz, 2MB flash
- Dual IMU (BMI088 + BMI270), SPL06 barometer, QMC5883L compass onboard
- AT7456E analog OSD, plus DisplayPort OSD on the HD VTX connector
- microSD card slot for logging
- Built-in Bluetooth telemetry on UART8, so you can connect a ground station without pairing
- 11 PWM outputs: DShot on all, bidirectional DShot on 1–8
- Dual regulators: 5V 3A for the receiver, GPS and sensors, and 12V 3A for the VTX and camera
Specifications
| MCU | STM32H743VIT6, 480MHz, 2MB flash |
|---|---|
| IMU | Dual: BMI088 + BMI270 |
| Barometer | SPL06 |
| Compass | QMC5883L onboard. An external I2C compass is supported. |
| OSD | AT7456E (analog), DisplayPort (HD) |
| Logging | microSD card slot |
| Telemetry | Built-in Bluetooth (UART8) |
| UARTs | 8 |
| PWM outputs | 11 (PWM 11 doubles as the LED pin) |
| Other interfaces | I2C, SWD, USB Type-C |
| Input voltage | 2–6S LiPo (VBAT pad only) |
| Regulators (BEC) | 5V 3A, 12V 3A |
| Mounting | 30.5 x 30.5mm (ø4mm holes) |
| Size | 36 x 36 x 8mm |
| Weight | 10g |
| Firmware | ArduPilot, PX4, INAV (8.0+), Betaflight |
Compatibility
- No ESC included. Pair it with a 30.5 x 30.5mm 4-in-1 ESC. For hex or octo builds, use single ESCs and a PDB, since there are 11 PWM outputs.
- Power: only the VBAT pad takes pack voltage (2–6S). Putting pack voltage on any other pin will damage the board.
- Compass: ArduPilot recommends a GPS with an external compass mounted away from power wiring, with the onboard compass disabled to avoid interference.
- Video: analog through the onboard OSD, or a DJI O3/O4 or other HD VTX through the 6-pin connector, which supplies 12V.
- V2 vs original: this is the V2 (SPL06, QMC5883L, 8 UARTs, USB-C). The original MicoAir743 is a different board, and its wiring guides don't match.
Works with (available at AeroFlow)
- FC + ESC stack: MicoAir743 V2 AM32 Stack
- GPS: MicoAir MG-F10, MicoAir M10G-5883, MicoAir MG-902
- 30.5mm 4-in-1 ESCs: SEQURE Blueson A2 AM32, TBS Lucid 6S 60A
- Telemetry: MicoAir LR900, MicoAir LR24
- Optical flow: MicoAir MTF-01, MicoAir MTF-01P
- Hex / octo PDB: GEPRC PDB Hexacopter, TBS Lucid PDB 500A
- Fixed-wing breakout: MicoAir PlaneIO Board
In the box
- 1x MicoAir743 V2 flight controller
- 1x 4GB TF card
- 7x connecting cables
- 4x rubber mats