GEPRC TAKER F405 BLS 65A V2 Stack

Rs. 8,599.00

Specifications

Weight (g)	22.2
Dimensions (mm)	FC 37.15 x 37.15; ESC 42 x 45.7
Cell count	3S, 4S, 5S, 6S
Voltage range	3-6S LiPo (ESC rated 3-8S, limited by FC)
Mount pattern	30.5 x 30.5mm, 4mm holes (3mm with the silicone grommets fitted)
Stack size	30.5 x 30.5mm
Connector	XT60
Output power	ESC 65A continuous, 70A burst (5s); FC BEC 5V/3A and 12V/2.5A
Compatibility notes	FC GEP-F405-HD V3: STM32F405, ICM42688-P (SPI), onboard barometer, 16MB blackbox, Betaflight OSD (AT7456E), 6 UARTs, M1-M6, Type-C, integrated LC filter, dual BEC 5V/3A + 12V/2.5A, direct DJI air unit plug. Target GEPRCF405. 37.15 x 37.15mm, 7.3g, 3-6S. ESC TAKER H65_8S_BLS: rated 3-8S, 65A continuous / 70A burst (5s), BLHeli_S target B_X_30, DShot150/300/600, current sensor. 42 x 45.7mm, 14.9g. The FC is 3-6S, so run this stack on 6S maximum. Both boards mount 30.5 x 30.5mm. Stack about 22.2g.
In the box	1x GEP-F405-HD V3 flight controller 1x TAKER H65_8S_BLS 65A 4-in-1 ESC 1x capacitor 1x DJI air unit adapter cable 1x flight controller adapter cable 1x XT60 power cable 4x M3x30 screws 4x M3x25 screws 8x nylon nuts 8x silicone grommets 2x SH1.0 4-pin silicone cables 1x camera connection cable

The GEPRC TAKER F405 BLS 65A V2 Stack pairs the GEP-F405-HD V3 flight controller with the TAKER H65_8S_BLS 65A 4-in-1 ESC — more current headroom than the 60A version in the same compact 42 x 45.7mm ESC footprint, for heavier freestyle and long-range builds. Direct DJI air unit plug included.

Features

Mainstream STM32F405 processor with the ICM42688-P gyro
16MB onboard blackbox for flight logs
Integrated LC power filter
Type-C USB port
Plugs straight into a DJI air unit — no soldering for HD video
Dual independent BEC: 12V @ 2.5A and 5V @ 3A
TAKER H65_8S_BLS 65A 4-in-1 ESC (BLHeli_S) for smooth motor response
Silicone shock-absorbing mounts keep the gyro stable

Flight controller (GEP-F405-HD V3)

MCU	STM32F405
Gyro (IMU)	ICM42688-P (SPI)
Barometer	Yes (onboard)
Blackbox	16MB onboard
OSD	Betaflight OSD (AT7456E chip)
UARTs	6
Motor outputs	M1–M6
BEC	5V @ 3A + 12V @ 2.5A, dual independent
Power filter	Integrated LC filter
USB	Type-C
Air unit	Direct plug-in for DJI air unit
Input voltage	3–6S LiPo
Size	37.15 x 37.15mm
Mounting	30.5 x 30.5mm (4mm holes, 3mm with silicone grommets)
Weight	7.3g
Firmware target	GEPRCF405

ESC (TAKER H65_8S_BLS 65A 4-in-1)

Continuous / burst	65A / 70A (5 seconds)
Input voltage	3–8S LiPo (ESC rating — see battery note below)
Firmware	BLHeli_S, target B_X_30
Protocols	DShot150 / DShot300 / DShot600
Current sensor	Yes
Size	42 x 45.7mm
Mounting	30.5 x 30.5mm (4mm holes, 3mm with silicone grommets)
Weight	14.9g

Compatibility

Battery: 6S maximum for this stack. The ESC alone is rated 3–8S, but the GEP-F405-HD V3 flight controller is 3–6S. XT60 power lead included.
Best for: heavier 5" and 6–7" builds. For a standard 5" see the 60A V2 Stack; for 7" and up see the 80A V2 Stack.
Frame: 30.5 x 30.5mm stack mount. Stack weight about 22.2g (FC 7.3g + ESC 14.9g).
Video: DJI air unit plug-in or analog VTX. Receiver: not included.