GEPRC TAKER H743 BT 8Bit 80A Stack
Rs. 14,999.00
Skip to product information
GEPRC TAKER H743 BT 8Bit 80A Stack
Rs. 14,999.00
Specifications
| Weight (g) | 36.5 |
|---|---|
| Dimensions (mm) | FC 38.5 x 38.5, ESC 56.3 x 61.1 |
| Cell count | 3S, 4S, 5S, 6S |
| Voltage range | 3-6S LiPo |
| Mount pattern | 30.5 x 30.5mm, 4mm holes (3mm with the silicone grommets fitted) |
| Stack size | 30.5 x 30.5mm |
| Connector | XT90 |
| Output power | ESC 80A continuous, 85A burst (5s); FC BEC 5V/3A and 12V/2.5A |
| Compatibility notes | Flight controller (TAKER H743 BT): STM32H743VIH6 with a Cortex-M7 core at 480MHz, dual gyro (MPU6000 plus ICM42688-P), barometer, 512MB onboard blackbox, Betaflight OSD with AT7456E, USB-C, integrated LC power filter, dual independent BEC 5V/3A and 12V/2.5A. Target GEPRC_TAKER_H743. 8.4g. Runs Betaflight, INAV or ArduPilot. 7 UARTs with UART3 permanently reserved for the Bluetooth module, which allows wireless parameter tuning from a phone. 8 motor outputs, so X8 configurations are supported. ESC (TAKER H80_BLS): 80A continuous, 85A burst for 5 seconds, DShot150/300/600, ammeter supported, BLHeli_S. Target B_X_30. 28.1g. Ships with a heavy-duty XT90 lead and a 4700uF capacitor. Plug-and-play ports for RX, DJI O3, VTX, buzzer, ESC and camera. Aimed at heavy-lift and long-range builds around 10-13 inch. |
| In the box | 1x TAKER H743 BT flight controller 1x TAKER H80_BLS 80A 4in1 ESC 1x 4700uF capacitor 1x XT90 power cable Screws, nuts and silicone grommets |
The GEPRC TAKER H743 BT 8Bit 80A Stack pairs a fast STM32H743 flight controller with an 80A 4-in-1 ESC for heavy-lift and long-range builds. It runs Betaflight, INAV and ArduPilot, has dual gyros, a barometer and 512MB blackbox, and supports eight motor outputs for X8 builds. Everything plugs in — no soldering needed for the DJI air unit.
Features
- STM32H743 (Cortex-M7, 480MHz)
- Dual gyro: MPU6000 + ICM42688-P
- 512MB onboard blackbox and barometer
- Eight motor outputs (X8 compatible)
- Dual independent BEC: 5V 3A and 12V 2.5A
- Direct-plug DJI air unit connection, integrated LC filter, Type-C USB
Flight controller (TAKER H743 BT)
| MCU | STM32H743 |
|---|---|
| Gyro | MPU6000 + ICM42688-P |
| OSD | Betaflight OSD (AT7456E) |
| UARTs | 7 |
| Input | 3–6S LiPo |
| Mounting | 30.5 x 30.5mm |
| Size | 38.5 x 38.5mm |
| Weight | 8.4g |
| Firmware target | GEPRC_TAKER_H743 |
ESC (TAKER H80_BLS 80A 4-in-1)
| Continuous / burst current | 80A / 85A (5s) |
|---|---|
| Input | 3–6S LiPo |
| Protocols | DShot150/300/600 |
| Current sensor | yes |
| Mounting | 30.5 x 30.5mm (M4, M3 with grommets) |
| Size | 56.3 x 61.1mm |
| Weight | 28.1g |
| Firmware target | B_X_30 |
Compatibility
- Frame clearance: the ESC board is 56.3 x 61.1mm - much larger than a standard 30.5 stack. It suits 7-13" long-range and heavy-lift frames; check it fits inside your frame before ordering.
- Battery: 3-6S. XT90 lead and 4700µF capacitor included.
- Firmware: Betaflight, INAV or ArduPilot - good for GPS / autonomous builds. 8 motor outputs for X8.
- Video: DJI O3 / O4 Pro plug-in (12V BEC) or analog.
Works with (available at AeroFlow)
- Frames: GEPRC Mark4-7, GEP-MOZ7 V2
- Motors: GEPRC SPEEDX2 2809, GEPRC EM3115 900KV, RCinPower Supernova 2810
- GPS: GEPRC GEP-M1025-DQ, MicoAir MG-F10
Note: GEPRC states that Bluetooth parameter tuning is not available on the current production batch.
In the box
- 1x TAKER H743 BT flight controller
- 1x TAKER H80_BLS 80A 4-in-1 ESC
- 1x 50V 4700µF capacitor
- DJI, receiver, camera, VTX and FC adapter cables
- 1x XT90 power lead (10AWG)
- Mounting screws, nylon nuts and silicone grommets