SEQURE H743 V2 & E160 G2 Stack

Rs. 14,699.00

Specifications

Weight (g)	73.3
Dimensions (mm)	FC 36.5 x 36.5 x 6, ESC 54 x 57 x 10
Cell count	4S, 5S, 6S, 7S, 8S, 9S, 10S, 11S, 12S
Voltage range	ESC 4-12S (14-53V) LiPo / LiHV; FC 4-8S
Mount pattern	30.5 x 30.5mm, 4mm holes / M3
Stack size	30.5 x 30.5mm
Connector	XT90H-M
Output power	ESC 160A continuous per channel, 280A peak; ESC BEC 16V 2A; FC BEC 5V/2.5A and 10V/2A
Compatibility notes	Flight controller: STM32H743, ICM-42688-P gyro, BMP280/DPS310/DPS368 barometer, AT7456E OSD, 16MB blackbox, 6 UARTs, 8 motor outputs, USB-C, dual BEC 5V/2.5A and 10V/2A for DJI O3/O4 air units. Betaflight target SEQUREH7V2; INAV and ArduPilot supported. 7.3g. ESC (E160 G2): STM32G071 processor, AM32 or BLHeli_32 firmware, all DShot rates plus OneShot, MultiShot and PWM, telemetry return and current sensing, 16V 2A BEC. 54 x 57 x 10mm, 66g. Two variants are selectable above, 8S 160A and 12S 160A. SEQURE publishes a single E160 G2 rated 4-12S, so the two options are the same board sold for different pack voltages - confirm with the supplier which is actually stocked. The flight controller is a 4-8S board; above 8S it is powered from the ESC BEC rather than pack voltage. Aimed at cinelifters and heavy-lift X8 builds.
In the box	1x SEQURE H743 V2 FC, 1x E160 G2 4-in-1 ESC 2x 63V 1200uF capacitors 1x XT90H-M connector, 2x 8AWG 150mm power leads 10x M3x10mm shock-absorbing washers, 4x M3x30mm screws, 4x M3 nylon nuts 1x 40mm SH1.0-8P cable, 2x 100mm SH1.0-4P cables 1x 5V buzzer

The SEQURE H743 V2 & E160 G2 Stack pairs the 480MHz SEQURE H743 V2 flight controller with SEQURE's E160 G2 4-in-1 ESC – 160A continuous and 280A peak per channel – for the heaviest cinelifters and X8 builds. The ESC uses low-resistance MOSFETs, a thick-copper multi-layer PCB with an on-board copper bar, dual power pads, current sensing and full telemetry, and runs AM32 or BLHeli_32. Choose the 8S or 12S option above.

SEQURE H743 V2 & E160 G2 Stack (8S 160A)

Features

E160 G2: 160A continuous / 280A peak per channel
STM32G071 ESC, AM32 or BLHeli_32, all DShot rates plus PWM, OneShot, MultiShot
Built-in current sensing; telemetry for RPM, temperature and current
Dual-pad power input for parallel batteries
H743 V2 FC with ICM-42688-P, barometer, OSD, 16MB blackbox, 8 motor outputs
Independent 10V 2A BEC for DJI O3/O4/O4 Pro and analog VTX

Flight controller (H743 V2)

STM32H743, ICM-42688-P, BMP280/DPS310/DPS368, AT7456E OSD, 16MB blackbox
6 UARTs, M1–M8 outputs, USB-C
Input 4–8S; BEC 5V 2.5A and 10V 2A
Firmware: Betaflight SEQUREH7V2 (default), INAV, ArduPilot
36.5 x 36.5 x 6mm, 7.3g

ESC (E160 G2 4-in-1)

Input	up to 12S LiPo/LiHV (8S and 12S options)
Current	160A continuous, 280A peak
BEC	16V 2A
Mounting	30.5 x 30.5mm (ø4mm / M3)
Size	54 x 57 x 10mm; weight 66g

Compatibility

Above 8S: the flight controller is a 4-8S board - on 12S it must be powered from the ESC's 16V BEC, not pack voltage.
8S or 12S option: SEQURE publishes one E160 G2 rated 4-12S; the two options are sold for different pack voltages. Choose the one matching your batteries.
Frame clearance: 54 x 57mm ESC on 30.5 holes - for heavy cinelifters, X8 and 13"+ builds.