SEQURE H743 V2 & E130 G2 Stack

Rs. 13,999.00

Specifications

Weight (g)	50.3
Dimensions (mm)	FC 36.5 x 36.5 x 6, ESC 54 x 57 x 7
Cell count	4S, 5S, 6S, 7S, 8S
Voltage range	ESC 4-8S (14-35.2V) LiPo / LiHV; FC 4-8S
Mount pattern	30.5 x 30.5mm, 4mm holes / M3
Stack size	30.5 x 30.5mm
Connector	XT90H-M
Output power	ESC 130A continuous per channel, 220A peak; ESC BEC 16V 2A; FC BEC 5V/2.5A and 10V/2A
Compatibility notes	Flight controller: STM32H743, ICM-42688-P gyro, BMP280/DPS310/DPS368 barometer, AT7456E OSD, 16MB blackbox, 6 UARTs, 8 motor outputs, USB-C, dual BEC 5V/2.5A and 10V/2A for DJI O3/O4 air units. Betaflight target SEQUREH7V2; INAV and ArduPilot supported. 7.3g. ESC (E130 G2): STM32G071 processor, AM32 or BLHeli_32 firmware, all DShot rates plus OneShot, MultiShot and PWM, telemetry return and current sensing, 16V 2A BEC. 43g. Heavy-lift and X8 oriented.
In the box	1x SEQURE H743 V2 FC, 1x E130 G2 4-in-1 ESC 2x 63V 1200uF capacitors 1x XT90H-M connector, 2x 8AWG 150mm power leads 10x M3x10mm shock-absorbing washers, 4x M3x30mm screws, 4x M3 nylon nuts 1x 40mm SH1.0-8P cable, 2x 100mm SH1.0-4P cables 1x 5V buzzer

The SEQURE H743 V2 & E130 G2 Stack pairs the 480MHz SEQURE H743 V2 flight controller with the E130 G2 4-in-1 ESC – 130A continuous per channel – for heavy-lift, cinelifter and X8 builds on 8S. The ESC uses low-resistance MOSFETs, a thick-copper multi-layer PCB with an on-board copper bar, dual power pads for parallel packs, current sensing and full telemetry, and runs AM32 or BLHeli_32.

SEQURE H743 V2 & E130 G2 Stack (8S 130A)

Features

E130 G2: 130A continuous / 220A peak per channel
STM32G071 ESC, AM32 or BLHeli_32, all DShot rates plus PWM, OneShot, MultiShot
Built-in current sensing; telemetry for RPM, temperature and current
Dual-pad power input for parallel batteries
H743 V2 FC with ICM-42688-P, barometer, OSD, 16MB blackbox, 8 motor outputs
Independent 10V 2A BEC for DJI O3/O4/O4 Pro and analog VTX

Flight controller (H743 V2)

STM32H743, ICM-42688-P, BMP280/DPS310/DPS368, AT7456E OSD, 16MB blackbox
6 UARTs, M1–M8 outputs, USB-C
Input 4–8S; BEC 5V 2.5A and 10V 2A
Firmware: Betaflight SEQUREH7V2 (default), INAV, ArduPilot
36.5 x 36.5 x 6mm, 7.3g

ESC (E130 G2 4-in-1)

Input	4–8S (14–35.2V) LiPo/LiHV
Current	130A continuous, 220A peak
BEC	16V 2A
Mounting	30.5 x 30.5mm (ø4mm / M3)
Size	54 x 57 x 7mm; weight 43g

Compatibility

Battery: 4-8S. XT90 connector and 8AWG leads - for large packs.
Frame clearance: the ESC is 54 x 57mm on 30.5 holes - meant for 10"+ cinelifters and heavy-lift frames.
Motors: large 28xx-42xx motors with 10-13" props.