Axisflying Argus F7 Plug-n-Play Stack
Pro (Aluminium Case) / 65A
Rs. 12,999.00
Skip to product information
Axisflying Argus F7 Plug-n-Play Stack
Rs. 12,999.00
Specifications
| Dimensions (mm) | Pro 48.6 x 46.6 x 26; Regular 48.6 x 44 x 20.8 (assembled stack) |
|---|---|
| Cell count | 3S, 4S, 5S, 6S |
| Voltage range | 3-6S LiPo (12.6-25.2V) |
| Mount pattern | 30.5 x 30.5mm, M3 |
| Stack size | 30.5 x 30.5mm |
| Output power | ESC 55A (65A burst) or 65A (75A burst); FC BEC 9V/2A and 5V/2A |
| Compatibility notes | Versions: Pro has both boards in a CNC full-aluminium case rated IP54 (splash-proof, not for underwater use) that acts as the heatsink; Regular is the same electronics as bare boards. Flight controller: STM32F722, ICM-42688P gyro (early batches BMI270), barometer and OSD, 16MB blackbox, 4 UARTs per Axisflying's current spec, up to 8 motor outputs, dual BEC 9V/2A and 5V/2A. Target AXISFLYINGF7PRO; Betaflight, and INAV on current firmware. ESC: BLHeli_32 (ST_G0_04), PWM 16-96kHz, telemetry and ammeter (current scale 400), no BEC. 55A version 55A/65A burst; 65A version 65A/75A burst. Direct plug connection for the DJI O3 air unit; analog and HD video both supported. |
The Axisflying Argus is a plug-and-play 30.5x30.5mm stack pairing an STM32F722 flight controller with a BLHeli_32 4-in-1 ESC for 3–6S builds. Choose the Pro version, where both boards sit in CNC full-aluminium covers rated IP54 that double as heatsinks, or the Regular version, the same electronics as bare boards for a lower, lighter stack. Each comes with a 55A or 65A ESC. Peripherals such as a DJI O3 air unit, analog camera and GPS plug straight in, no soldering.
Features
- Pro: CNC aluminium covers, IP54 dust and splash resistance, built-in heatsinking (not for underwater use)
- 55A or 65A ESC with large low-resistance MOSFETs, BLHeli_32 at up to 96kHz
- Up to 8 motor outputs for X8 builds; barometer and OSD
- Dual BEC: 9V 2A and 5V 2A
- Direct plug-in for the DJI O3; HD and analog both supported
- Status LEDs to check FC working state at a glance
Which version?
| Pro (Aluminium Case) | Regular | |
| Protection | CNC aluminium covers, IP54 | Bare PCBs |
| Assembled size | 48.6 x 46.6 x 26mm | 48.6 x 44 x 20.8mm |
| Weight | 59g | About 31g (Axisflying figure) |
Flight controller (Argus F7)
| MCU | STM32F722 |
|---|---|
| Gyro | ICM-42688P (early batches BMI270) |
| Blackbox | 16MB |
| UARTs | 4 per Axisflying's current spec (some resellers list 6 for early boards) |
| Motor outputs | Up to 8 (X8 PWM) |
| BEC | 9V 2A, 5V 2A |
| Firmware target | AXISFLYINGF7PRO (Betaflight; INAV supported on current firmware) |
| Also supported | ESC sensor, LED strip, buzzer, GPS |
ESC
| Current | 55A: 55A continuous, 65A burst 65A: 65A continuous, 75A burst (under 10s) |
|---|---|
| Firmware | BLHeli_32 (target ST_G0_04), PWM 16–96kHz |
| Telemetry | Yes, with current sensor (scale 400); no BEC |
| Input | 3–6S LiPo |
| Mounting | 30.5 x 30.5mm, M3 |
Compatibility
- Height: the Pro stack is 26mm tall and the Regular 20.8mm - many 5" frames limit stack height to 19-23mm, so the Pro may not fit where the Regular does. Check your frame before ordering.
- Frame: needs 30.5 x 30.5mm stack holes. Axisflying's own Manta5 Pro (20x20 only) does not take it.
- 55A or 65A: 55A suits most 5" freestyle builds; pick 65A for heavier 6-7" or high-current setups.
- Firmware: Betaflight, and INAV on current Axisflying firmware - flash the latest target before a GPS-navigation build.
- Battery: 3-6S. Video: analog OSD or DJI air unit plug-in (9V BEC).
Works with (available at AeroFlow)
- Motors: Axisflying AE2505